SLC-3-60 Series High-Power Street Light Loop Automatic Voltage Stabilization Control Box

 SLC-3-60 Series High-Power Street Light Loop Automatic Voltage Stabilization Control Box consists of a compensation transformer, voltage regulation transformer, non-contact control technology (or non-voltage regulation control technology), sampling circuit, main control circuit, voltage regulation control circuit, time control circuit, and protection circuit. Based on the characteristics of the lighting load and the actual grid voltage, it performs phase-separated sampling and phase-separated voltage stabilization and regulation. It integrates intelligent voltage stabilization, surge suppression, harmonic filtering, and power factor improvement into a single, innovative design, ensuring stable and reliable operation.

 High-Power Street Light Intelligent Lighting Voltage Stabilization and Dimming System Startup Operation Instructions

(1) Wiring: According to the labels inside the control cabinet, correctly connect the input and output cables. Check whether the control circuit is intact and whether the switches are closed.

Note: The neutral wire must be in good condition; otherwise, it may damage the equipment.

(2) Buttons, Switches, and LCD Display on the Front Panel

1. Manual/Automatic Selection Switch: Choose manual or automatic operation. In manual mode, use the start/stop buttons to control the lighting output. In automatic mode, the lighting output is controlled by a programmable system.

2. Start/Stop Buttons: In manual mode, press the green button to start the device and bypass. Press the red button to stop the device and bypass.

3. Device Automatic/Bypass Automatic Switch: In automatic mode, choose between device automatic or bypass automatic.

(3) Operating Parameter Settings

1. Current Date and Time Setting: After the control cabinet is powered on, the current date and time displayed on the LCD may not match the actual date and time. Reset them via the LCD display as follows:

a. Move the microswitch on the voltage stabilizer controller (inside the control cabinet) to the Stop position. The orange indicator light on the controller will illuminate.

b. In automatic mode, use the up and down buttons below the display to select the date setting screen. Press Enter to enter the setting mode. Use the up and down buttons on the right side of the display to modify the parameter at the cursor. Use the left and right buttons to move the cursor. Press Enter to confirm after setting.

c. Select the time setting screen and modify the time, same as step b.

d. After setting the date and time, move the microswitch on the controller (inside the control cabinet) to the Run position. The green indicator light on the controller will illuminate. The settings will take effect.

SLC-3-60 Series High-Power Street Light Loop Automatic Voltage Stabilization Control Box Technical Parameters 

Input Power: Voltage Single-phase 120V, 220V, 230V, 240V

Three-phase 208V, 220V, 230V, 240V, 380V, 400V, 415V+N+Gr

Regulation Range +25%/-5%

Rated Voltage  +11%/-19%

Energy-Saving Voltage  +10%/-25%

Energy-Saving Voltage (HPSV) 48-63Hz

Phase Protection Single-pole U-shaped circuit breaker per phase

Output Power:  Voltage 180V (between phase and neutral), adjustable based on lamp type

Recommended Value: MV 111

Voltage: 190VAC111 MPS

Voltage: 180VAC

Harmonic Distortion None

Power Factor 0.5 leading to 0.7 lagging

Lamp Selection MV, HPSV (via microswitch)

The selection of an intelligent street light controller solution primarily involves choosing between a PLC solution and a microprocessor solution.

Solution 1: Adopt upper and lower computer ( ) control.

Solution 2: Use TI's DSP controller or an ARM embedded system for control.

Solution 3: Use ATMEL's AT89S52 microcontroller for control.

 Series High-Power Street Light Intelligent Lighting Voltage Stabilization and Dimming System offers excellent performance, high reliability (mean time between failures 30,000-50,000 hours), simple programming, and strong versatility, making it suitable for applications requiring extensive switching control.

Functional Indicators:

Dynamically track input voltage and automatically adjust energy-saving levels to keep lamps operating at a constant voltage, ensuring normal operation and achieving energy-saving effects.

Multi-layer protection: Comprehensive lightning protection, overvoltage protection, and overheating protection.

Extended lifespan of electric light sources.

Manual/Automatic Adjustment: Both bypass and energy-saving levels can be adjusted manually or automatically. Even if the energy-saving device fails, normal lighting power supply operation can be maintained.

The lighting device features manual and automatic functions and supports remote control. The default factory setting is automatic function.